About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features Press Copyright Contact us Creators. This document is still useful in the case of a Firewire device not yet supported by ALSA or as a work around if a bug is found in the ALSA drivers. Ubuntu 11.04 ('Natty Narwhal') completed the migration to the new FireWire driver stack, and the legacy firewire stack was removed with the 2.6.37 kernel.

1. Firewire 410 Windows 10
2. Firewire 410
3. Firewire 410 Driver Mac

Most Firewire devices now have ALSA support and should just work in the same way as all ALSA supported devices Work. This document is still useful in the case of a Firewire device not yet supported by ALSA or as a work around if a bug is found in the ALSA drivers.

Ubuntu 11.04 ('Natty Narwhal') completed the migration to the new FireWire driver stack, and the legacy firewire stack was removed with the 2.6.37 kernel. Refer to FireWire Stacks Explained for more details.

Older Releases

For completeness, there is still documentation to provide ALL the steps needed to configure an older system to use a FireWire device. However, most of these extra configuration steps are no longer required, beyond what is needed to use any other soundcard with JACK in realtime mode.

Newer Releases

UbuntuStudio 12.04 LTS ('Precise Pangolin') ships with the lowlatency kernel, and the 'audio' group is preconfigured with proper security and user settings, so it should 'just work'.

If you are using Ubuntu 11.04 ('Natty Narwhal') or a later release, its configuration should be verified.

To use your FireWire device, enter the procedure at Set IRQ Priorities.

Even Newer Releases

The ALSA team has integrated the FFADO code into ALSA drivers. Therefore between Linux 2.6.39 and 4.4 the Firewire code has been added to ALSA and Ubuntu comes with the ALSA modules configured and the FFADO modules blacklisted. This means that a firewire device should be used in the same way as any other ALSA device. As such most of this tutorial should not apply and the generic ALSA instructions should be used instead. If the ALSA modules either don't support your Firewire device or don't support it as well as FFADO has in the past, then the user will have to blacklist the ALSA firewire modules and comment out the blacklisting of the FFADO modules. A list of the ALSA Firewire modules can be found at: The ALSA Firewire Stack

Firewire 410 Windows 10

Supported FireWire Audio Devices

Refer to this list of currently supported devices.

Note: This wiki has two other entries which are relevant to Firewire:

1. Firewire describes the use of IEEE 1394 firewire video devices.

2. Preparing UbuntuStudio for Firewire is mostly out of date, but describes the use of IEEE 1394 firewire sound cards and cameras.

Set IRQ Priorities

Note: This step is not applicable unless you have Ubuntu 10.10 ('Maverick Meerkat') or a later release, with a realtime, lowlatency, or a kernel at 2.6.39 or later.

One of the biggest advantages of a realtime kernel is the ability to prioritize IRQ's. This feature can increase the stability of applications which need to capture data with low latencies.

UbuntuStudio 12.04 LTS ('Precise Pangolin') ships with the lowlatency kernel preconfigured to support realtime irq priorities. This feature is also available in the lowlatency kernel, as of 2.6.39, but you might need to add 'threadirqs' (without the quotes) to the boot command line to enable this feature (if not using UbuntuStudio).

The real-time IRQ priorities are set during system boot by the /etc/init.d/rtirq script. By default, sound cards and USB devices are given a high priority but firewire devices are not. If the firewire driver and jackd cannot process the incoming data quickly enough, then jackd will discard the data buffers and notify the audio application of the overrun event (usually called an xrun).

To reduce the risk of overruns, you need to change this configuration file:

The priorities are set, in order from highest to lowest, by these two lines:

Firewire 410

You need to ensure the firewire device receives higher priority for its interrupt handler than everything other than the real time clock, so you should put the name of the firewire driver second in both the lists, i.e. insert firewire in the second place of these lists, so they look like this:

Note: This assumes you are using the new firewire stack with an internal controller. If you need to use the old stack, use the ohci1394 driver instead. If your firewire card is handled by an external controller (e.g. a PC-Card), you need to code the name of the card controller module (e.g. yenta). If you are not sure, then read FireWire stacks explained for more information.

Reboot your system (or just run sudo service rtirq start) to assign your new IRQ priorities. sudo service rtirq status will show you the current status: the firewire irq should appear second on the list, probably with an RTPRIO of 85.

There are more IRQ adjustments that can be made and may be beneficial, but they are not easily automated by the rtirq script. To learn how to tweak things even further, see http://subversion.ffado.org/wiki/IrqPriorities for more detailed information.

Start Jack

Before running jackd and your audio capture application, you should stop any programs that might contend for system resources. Many users find it helpful to stop all networking activity and, in particular, polling for wireless networks can cause unexpected xruns.

• Open the jack control gui application. On newer systems this is the QjackCtl entry in the Audio Production menu. On older systems, it is Jack Control in the Sound & Video/Audio Production menu.

• Click 'Setup'. Here are some good settings to start with:
  • Driver: firewire (This selects the ffado driver stack)
  • Interface: hw:0

  • Audio:Duplex

  • Check Realtime
  • Priority: (default)
  • Frames/Period: 128
  • Sample Rate: 44100
  • Periods/Buffer: 3
• Click 'OK', then click 'Start'. After a few seconds Jack Control should display CPU percentage, RT should be yellow and blinking, and x-runs should be at 0/0.

• Note: You should adjust your Sample Rate to match the clock rate of your firewire device! e.g. 44100 for CD quality audio, 48000 for video work, higher for studio quality.

• The default priority is claimed elsewhere to be 10, but this will usually be OK. A higher number will reduce the risk of xruns, but you need a lower priority than that of the irq driver
• Frames/Period can be lowered as well. A lower number will yield lower latencies and use more processor power. If you start getting xruns, increase this number and accept a higher latency.
• Setting Frames/Period to 64 and Periods/Buffer to 3 should result in a round-trip latency of just under 10ms, which is generally considered negligible.

Have Fun and Happy Audio Production!

Firewire 410 Driver Mac

For ideas on where to go from here, see UbuntuStudio/Audio

CategoryAudio