IC-2730 Radio Programming Software The WCS-2730 helps you program memory channels and other set menu items for the Icom IC-2730 radio. Easy to use spreadsheet design completes memory channel options automatically. 3.4m (11.2ft) OPC-1712 SEPARATION CABLE. 10cm (3.9in) Same as supplied. OPC-1529R DATA COMMUNICATION CABLE. Allows you data communication in DV mode and PC cloning with. CS-2820 CLONING SOFTWARE. For quick and easy programming of memories, etc. Either OPC-1529R or OPC-478 is required. OPC-478 CLONING CABLE.
- Icom programming software allows you to set frequencies and functions within your Icom radio. Also know as Icom Cloning Software, this software is easy to use and runs on your PC under the Windows Operating System. You can set each channels frequency and privacy codes, set functions for each programmable key on your radio, set parameters such as delay time for the Time-Out-Timer, and many.
- Intel.com software icom software for mac Download 9edf636fed ICOM IC-F5021 CLONING Software and Latest Firmware F5021.
Icom Programming Cable Schematic
Icom Programming Cable
Free Icom Programming Software
Download Information
All N4PY software programs are available for free for the first 10 days of use. If you decide you want to use the program after the trial period, please follow the instructions below.
Payment Method
For Paypal, go to the PURCHASE page.
Please put your call sign, radio type, and email address in the comment section of the PayPal page.
For check payment, make the check payable to Carl Moreschi and PLEASE include your EMAIL address, call sign, and radio type you will be using. All checks must be in US dollars from a US bank. I do not wait for the checks to clear.
Mail Checks to:
Carl Moreschi
127 River Moss Way
Hertford, NC 27944
If you do not have Internet access and want the software on
diskette or CD, there is an additional charge of $10.00 for
a diskette or CD mailed directly to you.
All N4PY software runs on windows operating systems Windows XP, Vista, and Windows 7, 8, and 10 (including the 64 bit versions of XP, Vista, and Windows 7, 8, and 10).
A password protection scheme is used by the program.
You can run the program for 10 days without a password. During this
time, you should send the install number along with your call sign
to n4py@arrl.net to get your password. Your password only needs
to be entered once. It is good for all following versions until your
subscription expires. When your subscription expires, you will still
be able to use versions that came out prior to your subscription
expiring. The same install number and password will allow multiple
versions to run on the same computer but not on another computer.
My policy to give everyone all the passwords they need for all
their own computers for their own use. The software license
goes with the person and not with the computer. The N4PY software
license is not transferable to another user.
Specific Download Information
To configure the program for your Icom radio:
a) Start the program.
b) Select 'Settings' at the top of the Radio screen.
c) In the 'Interface' window, select the correct Icom radio from the
radio type list box.
d) Leave the CI-V address set at 'Default'.
e) Select the correct baud rate. 19200 is highly recommended.
Make sure the radio also matches this baud rate.
f) Depending on what kind of CI-V to serial converter you are using,
you may need to turn on serial power. For the CT-17, you don't
need either of the serial power boxes turned on. For other CI-V
converters if you don't know, turn on both 'Use DTR to power
serial interface' and 'Use RTS to power serial interface'.
g) Select the correct comport.
h) Exit the program.
i) Start the program again and you should be running.
Changes from version 3.40 to version 3.41
1)
Added TUNE as a new pod selection.
2)
Added the Numark DJ2GO2 Touch DJ Controller.
3)
Fixed crash when using 4O3A Antenna Genius.
4)
Put the ACOM 2000 old controller interface back in for those users
with the old ACOM controller.
All N4PY software programs are available for free for the first 10 days of use. If you decide you want to use the program after the trial period, please follow the instructions below.
Payment Method
For Paypal, go to the PURCHASE page.
Please put your call sign, radio type, and email address in the comment section of the PayPal page.
For check payment, make the check payable to Carl Moreschi and PLEASE include your EMAIL address, call sign, and radio type you will be using. All checks must be in US dollars from a US bank. I do not wait for the checks to clear.
Mail Checks to:
Carl Moreschi
127 River Moss Way
Hertford, NC 27944
If you do not have Internet access and want the software on
diskette or CD, there is an additional charge of $10.00 for
a diskette or CD mailed directly to you.
All N4PY software runs on windows operating systems Windows XP, Vista, and Windows 7, 8, and 10 (including the 64 bit versions of XP, Vista, and Windows 7, 8, and 10).
A password protection scheme is used by the program.
You can run the program for 10 days without a password. During this
time, you should send the install number along with your call sign
to n4py@arrl.net to get your password. Your password only needs
to be entered once. It is good for all following versions until your
subscription expires. When your subscription expires, you will still
be able to use versions that came out prior to your subscription
expiring. The same install number and password will allow multiple
versions to run on the same computer but not on another computer.
My policy to give everyone all the passwords they need for all
their own computers for their own use. The software license
goes with the person and not with the computer. The N4PY software
license is not transferable to another user.
Specific Download Information
To configure the program for your Icom radio:
a) Start the program.
b) Select 'Settings' at the top of the Radio screen.
c) In the 'Interface' window, select the correct Icom radio from the
radio type list box.
d) Leave the CI-V address set at 'Default'.
e) Select the correct baud rate. 19200 is highly recommended.
Make sure the radio also matches this baud rate.
f) Depending on what kind of CI-V to serial converter you are using,
you may need to turn on serial power. For the CT-17, you don't
need either of the serial power boxes turned on. For other CI-V
converters if you don't know, turn on both 'Use DTR to power
serial interface' and 'Use RTS to power serial interface'.
g) Select the correct comport.
h) Exit the program.
i) Start the program again and you should be running.
Changes from version 3.40 to version 3.41
1)
Added TUNE as a new pod selection.
2)
Added the Numark DJ2GO2 Touch DJ Controller.
3)
Fixed crash when using 4O3A Antenna Genius.
4)
Put the ACOM 2000 old controller interface back in for those users
with the old ACOM controller.